Advanced plasma technology marks a new millennium in the global wood market
About drying device About drying device
About drying device

Advanced wood processing technology using microwave!

A global company specializing in the energy and eco-friendly business field based on plasma technology,
the basic science of the 4th industrial revolution!
This technology works by attaching a module that generates microwaves to the chamber, and generates heat from the inside of the wood by evenly radiating microwaves to the wood through the module, allowing the wood to dry and evenly shrink in a short time, dramatically reducing splitting and warping, and thus dry high quality wood.
1. Product name
PACEP wood sterilizing and drying device (model name: MAMA-8H)
2. Specifications
① Output 18 2.45GHz Microwave 3kw modules = 54kw total
Module specification Up to 1.2 kw/hr class Magnetron 3ea
3 Switched-Mode Power Supply / 7 cooling fans 55w/hr
1 module power consumption 3.7 kw/hr max
② Power consumption Up to 72KVA or less (including control and fan power)
③ Size specification Maximum size of treated wood Width 500 Height 900 Length 7,200 (mm)
Internal standard of processing chamber Width 1,000 Height 1,000 Length 8,000 (mm)
External standard of processing device Width 1,500 Height 1,300 Length 17,000 (mm) (External connecting rail 8,500 mm)
④ Input power 380V 3-phase, 4-wire (power 3-wire, neutral)
grounding 3 kinds of grounding or more
⑤ Control panel Main block switch 200A (recommended)
Microwave output on/off general control, time control (operation and pause time))
Microwave output on/off for each module
⑥ External air supply fan 6 units of 25watt class
⑦ Material inner side plate; steel, structure bar & others; steel
3. Operation measurement and instrumentation (PLC panel)
① Displays input phase voltage, current and accumulated power digitally
② Displays voltage, current, power consumption, and computational power for each module in each phase for each module.
③ Displays voltage, current, and computed wattage for each module and each phase of 3 input phases
4. Safety shut-off device
① Input power emergency shut-off switch
② Operation cut-off switch for each phase
5. Safety device: A safety device in case of continuous operation of one module
① In the case the heat of the power element exceeds the specified value, automatic shutdown
② In the case the magnetron element heat generation exceeds the specified value, automatic shutdown
6. Ground reference
Grounding above 3 types
7. Spare Module
Spare modules: 2 (recommended)
8. Driving preference
① For the purpose of drying wood, it is recommended not to continue operate by exceeding 180 minutes.
② n the case the device is made of sus, when corrosive compounds such as acetic acid are used, the operator must pay attention not to affect corrosion on modules and systems outside the chamber by having a device that collects gas through the vent. (As this product is made of steel, the use of corrosive compounds is prohibited)
③ The operator must check the locking device on the entrance side of the wood outside the device, and severe electromagnetic leakage caused by non-compliance must be the responsibility of the operator.
④ If continuous heating is prolonged, a lot of water condenses inside. So, the operator should clean it using absorbent materials. Neglecting this may cause internal corrosion and shortening of device life.
⑤ If equipment is used in a dusty place, it is recommended that the module is cleaned regularly and the filter is cleaned.

Head Office : 130-50, Palgoe-ro, Yeongwol-eup, Yeongwol-gun, Gangwon-do
                   (Yeongwol No.3 Agricultural and Industrial Complex), Republic of Korea
Factory : 130-40, Palgoe-ro, Yeongwol-gun, Gangwon-do (203,Yoengwol Business Incubation Center), Republic of Korea
Branch Office: 77, Gongdan3-ro, Donghae-si, Ganwod-do, Republic of Korea
Tel. +82)33-373-1349H.P. +82)10-5643-1349Fax. +82)33-372-1349|pacep1@daum.net